What readback items are always required when receiving taxi instructions from ATC?

4-3-18. Taxiing
a. General. Approval must be obtained prior to moving an aircraft or vehicle onto the movement area during
the hours an Airport Traffic Control Tower is in operation.
1. Always state your position on the airport when calling the tower for taxi instructions.
2. The movement area is normally described in local bulletins issued by the airport manager or control
tower. These bulletins may be found in FSSs, fixed base operators offices, air carrier offices, and operations
offices.
3. The control tower also issues bulletins describing areas where they cannot provide ATC service due to
nonvisibility or other reasons.
4. A clearance must be obtained prior to taxiing on a runway, taking off, or landing during the hours an
Airport Traffic Control Tower is in operation.
5. A clearance must be obtained prior to crossing any runway. ATC will issue an explicit clearance for all
runway crossings.
6. When assigned a takeoff runway, A TC will first specify the runway, issue taxi instructions, and state any
hold short instructions or runway crossing clearances if the taxi route will cross a runway. This does not authorize
the aircraft to "enter" or "cross" the assigned departure runway at any point. In order to preclude
misunderstandings in radio communications, ATC will not use the word "cleared" in conjunction with
authorization for aircraft to taxi.
7. When issuing taxi instructions to any point other than an assigned takeoff runway, ATC will specify the
point to taxi to, issue taxi instructions, and state any hold short instructions or runway crossing clearances if the
taxi route will cross a runway.
NOTE-
ATC is required to obtain a readback from the pilot of all runway hold short instructions.
Airport Operations 4-3-23

AIM 2/20/25
8. If a pilot is expected to hold short of a runway approach/departure ( Runway XX APPCH/Runway XX
DEP) hold area or ILS holding position (see FIG 2-3-15, Taxiways Located in Runway Approach Area), ATC
will issue instructions.
9. When taxi instructions are received from the controller, pilots should always read back:
(a) The runway assignment.
(b) Any clearance to enter a specific runway.
(c) Any instruction to hold short of a specific runway or line up and wait.
10. Controllers are required to request a readback of runway hold short assignment when it is not received
from the pilot/vehicle.
b. ATC clearances or instructions pertaining to taxiing are predicated on known traffic and known physical
airport conditions. Therefore, it is important that pilots clearly understand the clearance or instruction. Although
an ATC clearance is issued for tax iing purposes, when operating in accordance with the CFRs, it is the
responsibility of the pilot to avoid collision with other aircraft. Since "the pilot -in-command of an aircraft is
directly responsible for, and is the final authority as to, the operation of that aircraft" the pilot should obtain
clarification of any clearance or instruction which is not understood.
1. Good operating practice dictates that pilots acknowledge all runway crossing, hold short, or takeoff
clearances unless there is some misunderstanding, at which time the pilot should query the controller until the
clearance is understood.
NOTE-
Air traffic controllers are required to obtain from the pilot a readback of all runway hold short instructions.
2. Pilots operating a single pilot aircraft should monitor only assigned ATC communications after being
cleared onto the active runway for departure. Single pilot aircraft should not monitor other than ATC
communications until flight from Class B, Class C, or Class D surface area is completed. This same procedure
should be practiced from after receipt of the clearance for landing until the landing and taxi activities are
complete. Proper effective scanning for other aircraft, surface vehicles, or other objects should be continuously
exercised in all cases.
3. If the pilot is unfamiliar with the airport or for any reason confusion exists as to the correct taxi routing,
a request may be made for progressive taxi instructions which include step- by-step routing directions.
Progressive instructions may also be issued if the controller deems it necessary due to traffic or field conditions
(for example, construction or closed taxiways).
c. At those airports where the U.S. Government op erates the control tower and ATC has authorized
noncompliance with the requirement for two-way radio communications while operating within the Class B,
Class C, or Class D surface area, or at those airports where the U.S. Government does not operate the control
tower and radio communications cannot be established, pilots must obtain a clearance by visual light signal prior
to taxiing on a runway and prior to takeoff and landing.
d. The following phraseologies and procedures are used in radiotelephone communications with aeronautical
ground stations.
1. Request for taxi instructions prior to departure. State your aircraft identification, location, type of
operation planned (VFR or IFR), and the point of first intended landing.
EXAMPLE-
Aircraft: "Washington ground, Beechcraft One Three One Five Niner at hangar eight, ready to taxi, I-F-R to Chicago."
Tower: "Beechcraft one three one five niner, Washington ground, runway two seven, taxi via taxiways Charlie and Delta,
hold short of runway three three left."
Aircraft: "Beechcraft One Three One Five Niner, runway two seven, hold short of runway three three left."
4-3-24 Airport Operations

2/20/25 AIM
2. Receipt of ATC clearance. ARTCC clearances are relayed to pilots by airport traffic controllers in the
following manner.
EXAMPLE-
Tower: "Beechcraft One Three One Five Niner, cleared to the Chicago Midway Airport via Victor Eight, maintain eight
thousand."
Aircraft: "Beechcraft One Three One Five Niner, cleared to the Chicago Midway Airport via Victor Eight, maintain eight
thousand."
NOTE-
Normally, an ATC IFR clearance is relayed to a pilot by the ground controller . At busy locations, however, pilots may be
instructed by the ground controller to "contact clearance delivery" on a frequency designated for this purpose. No
surveillance or control over the movement of traffic is exercised by this position of operation.
3. Request for taxi instructions after landing. State your aircraft identification, location, and that you
request taxi instructions.
EXAMPLE-
Aircraft: "Dulles ground, Beechcraft One Four Two Six One clearing runway one right on taxiway echo three, request
clearance to Page."
Tower: "Beechcraft One Four Two Six One, Dulles ground, taxi to Page via taxiways echo three, echo one, and echo niner."
or
Aircraft: "Orlando ground, Beechcraft One Four Two Six One clearing runway one eight left at taxiway bravo three, request
clearance to Page."
Tower: "Beechcraft One Four Two Six One, Orlando ground, hold short of runway one eight right."
Aircraft: "Beechcraft One Four Two Six One, hold short of runway one eight right."
e. During ground operations, jet blast, prop wash, and rotor wash can cause damage and upsets if encountered
at close range. Pilots should consider the effects of jet blast, prop wash, and rotor wash on aircraft, vehicles, and
maintenance equipment during ground operations.